1992 Peterbilt Transporter VIN: 1XPDDR9X3ND606871 Purchased in 1998 by Canepa Concept Transporters, this rig was a ground up conversion of an excellent, one owner Peterbilt truck with 500k miles. The rig was stripped down, the frame stretched to a wheelbase of 280 inches, new high-speed rear ends installed and then the rebuilding began. The engine received a new camshaft and full service, the transmission was rebuilt, and the Jake brake refurbished. A new van body was installed and outfitted as a 4-car transporter to an extremely high level of finish. No expense was spared inside or out: A-C and heat in both the sleeper front and the van rear; air compressor system, high output diesel generator, full electrical 110v and 220v; lighting and tent system; reinforced roof with a 30 person capacity. The list goes on and on. Bruce Canepa then finished off the design with custom body panels and a show quality black paint job leaving the truck considerably more aerodynamic and certainly more attractive. Don Orosco has owned the vehicle since its build. In that time it has logged only 112k miles, was regularly maintained, and has always been stored indoors. The construction detailing of this rig is of the highest quality. To build such a truck today would cost in excess of $400k. This custom 4-car transporter presents tremendous value for the money. Don says of this amazing rig: Of the four transporters I have owned and used over the past thirty years, this is undoubtedly the easiest to use and most user friendly. Key features: 3406 Caterpillar 425 HP diesel engine Jake brake and thirteen speed gearbox Dual rear axles with high speed rear end drive ratios to facilitate high speed running. Both rear axles drive Alcoa aluminum truck wheels throughout with low mile tires mounted Air ride system with adjustable height Body is entirely sheathed in .090 aluminum Stainless steel, under body, parts storage pullout compartments Built in, quick release air couplers throughout 6000 pound rated lift gate Internal, electrically operated, hydraulic lift gate for aft car position Air conditioned- heated box van area Fully re-upholstered cab and in-cab bunk bed Stowable work bench with vice Complete Concept awning, with fully enclosed side panels Flush mounted E track anchoring system the entire length of the floor Large, reinforced, roof mounted, observation deck with fold out stainless steel railings and tent roof. Stainless steel stair system for access to observation deck High output, 20Kw, under body water-cooled diesel generator with automatic switch gear with 1680 hours of running time to date Interior ramping to accommodate four vehicles On board, quick recovery air compressor automatically tied to under bed diesel generator through switch gear capable of keeping up with the demands of any air tools, impact wrenches, etc. Plug in, outside, high intensity lights for loading and under tent operations Build Details: Mechanical Refurbishment by Diesel Performance: New rear ends New cam shaft New heater Frame stretch Transmission refurbishment Jake brake refurbishment Aircraft Side Access Door: 32 x 84 opening size Spring assist open and closing 10 ga. formed structural steel perimeter door frame inside trailer wall 10 ga. formed steel header inside trailer wall below top rail Structural reinforcements added to crossmembers and floor in door area Composite door construction Rivetless exterior construction Lightweight 2 piece 14 ga. formed steel door structure .090 5052 rivetless aluminum exterior panel: unpainted .125 5052 custom formed aluminum stairs - interior panel with non-skid tape applied on step surface All steel surfaces primered for rust prevention Recessed polished stainless steel positive latching lockable door latch with concealed hardware Long lasting corner mounted door seal Stainless steel piano hinge with internal compression seal Removable polished stainless steel round tube handrail Stainless steel trim around door for water deflection Box-Van Belly Box Package: Painted gray 14 ga. steel frame construction Polished 16 ga. 304 #8 stainless steel belly box doors 2 polished stainless steel T-handle lockable latches per door 2 gas springs per door: to hold doors open Full length vinyl covered stainless steel piano hinge on each door 1 custom Lista ST-600 cabinet mounted in curbside middle box Belly Box Drawers: 14 ga. stainless steel construction

Year:  1992
Miles:  110 000 - 119 999
Transmission: Manual
Important Safety Tips
  • Meet the seller and test drive before you buy.
  • Be cautious of underpriced items.
  • Don’t wire money or take advance payments.
  • Only pay for shipping if you know the seller.
To learn more, visit the Safety Center or click here to report this listing.

Copyright © 2018 Americanlisted.com, All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.